Dry Ice Blasting Mold

Cryogenic mold removal that kills spores without water damage

Dry Ice Blasting Mold in VALLEY VILLAGE, California

Dry Ice Blasting Mold in VALLEY VILLAGE, California is the cleanest way to strip mold off structural lumber, brick, and HVAC components without soaking your home. We use dry ice mold removal in VALLEY VILLAGE to freeze spores on contact and lift them off the surface, so you avoid the secondary water damage that pressure washing and chemical washes leave behind. If you have black mold growth in a crawl space, attic, or bathroom, call (833) 929-5837.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What Our Dry Ice Blasting Mold Service Includes

Every dry ice blasting mold job in VALLEY VILLAGE includes the full remediation process, from inspection to clearance testing. We do not sell blasting as a standalone service, because blasting without containment and post-remediation testing just spreads spores around. Here is what is covered in the fixed price.

01

Full Mold Inspection

We inspect with a moisture meter, thermal imaging camera, and borescope camera to map the mold and find the water source. You get photos, moisture readings, and a written scope within 24 hours. This step takes 60 to 90 minutes on a typical home.

02

Containment And Negative Air

We build a containment barrier with polyethylene sheeting and run a negative air machine with HEPA filters to keep spores out of clean areas. HVAC registers get sealed before blasting starts. Setup takes about two hours on a 500 sq ft containment.

03

Dry Ice Blasting

A two-person crew runs the dry ice blasting machine at 300 to 500 mph with minus 109 degree Fahrenheit pellets. We consume 300 to 600 pounds of dry ice per shift. Most residential jobs finish in one day, and commercial jobs run two to five days.

04

HEPA Vacuum And Antimicrobial

After blasting, we vacuum every surface with a HEPA vacuum and apply an antimicrobial solution like Concrobium or Benefect. Porous surfaces get an encapsulant coating. This step adds two to three hours to the job and is included in the price.

05

Post-Remediation Testing

We run a spore trap sampler inside the containment and outside as a control, then compare the counts. You get the third-party lab report and a clearance document for your records or insurance claim. Results come back in 24 to 48 hours.

Service overview

What Dry Ice Blasting Mold in VALLEY VILLAGE, California Does

Dry Ice Blasting Mold in VALLEY VILLAGE, California is a cryogenic cleaning method that fires rice-sized dry ice pellets at 300 to 500 mph through a pressurized blasting machine. The pellets hit mold at minus 109 degrees Fahrenheit, freezing the growth and causing it to crack and release from the substrate. Because the dry ice sublimates into carbon dioxide gas on impact, there is no water, no sand, and no chemical residue left behind. We use it on structural framing, subflooring, brick, concrete, and HVAC plenums where moisture-based cleaning would cause more harm than good.

VALLEY VILLAGE sits in a warm, dry pocket of the San Fernando Valley, but that does not stop mold. Older ranch homes and 1960s apartment buildings here have original galvanized plumbing that sweats, and slab leaks feed hidden moisture into wall cavities for months before anyone notices. We see attic mold after every Santa Ana wind event, crawl space mold from poor vapor barriers, and HVAC mold contamination in buildings where the condensate line has been clogged since last summer. Dry ice mold removal in VALLEY VILLAGE handles all three without tearing the structure apart.

No Secondary Water DamagePressure washing and wet chemical treatments push water into wood, drywall, and insulation, which is exactly what mold needs to spread. Dry ice blasting leaves the substrate dry. On a typical 1,200 sq ft crawl space, we finish in four to six hours and the framing is ready for encapsulation the same day, with no drying equipment required.
Reaches Hidden FramingWe use a borescope camera to inspect inside wall cavities before we start, then blast through access ports without full demolition. That saves you the cost of tearing out and rebuilding drywall. On a recent Valley Village job, we removed mold from 40 linear feet of stud bay through six small ports instead of removing 200 sq ft of drywall.
Kills Spores On ContactThe thermal shock of minus 109 degrees Fahrenheit freezes mold spores and mycelium, and the kinetic impact lifts them off the surface. We follow with a HEPA vacuum and an antimicrobial solution to catch anything airborne. Post-remediation mold testing with a spore trap sampler confirms the spore count has returned to normal outdoor levels.
Dry Ice Blasting Mold by Mold Remediation Service Valley Village
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

Our Dry Ice Blasting Mold Process

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Inspection And Testing

We start with a moisture meter, thermal imaging camera, and borescope camera to map the mold and find the water source. Air samples go to a third-party lab. You get the lab results and a written scope within 24 hours. This step takes 60 to 90 minutes on a typical home.

Stage 1
02

Containment Setup

We build a containment barrier with polyethylene sheeting and negative air ducting, then install a negative air machine with HEPA filters to keep spores from spreading to clean areas. On a 500 sq ft containment, setup takes about two hours. We seal HVAC registers and doorways before any blasting begins.

Stage 2
03

Dry Ice Blasting

A two-person crew runs the dry ice blasting machine. One technician blasts while the other manages the HEPA vacuum at the containment edge. We work in four to six hour shifts and consume 300 to 600 pounds of dry ice pellets per shift depending on the surface. Most residential jobs finish in one day.

Stage 3
04

HEPA Vacuum And Antimicrobial

After blasting, we vacuum every surface with a HEPA vacuum, then apply an antimicrobial solution such as Concrobium or Benefect to the cleaned framing. On porous surfaces like raw lumber, we follow with an encapsulant coating. This step adds two to three hours to the job.

Stage 4
05

Post-Remediation Testing

We run a spore trap sampler and compare the indoor count to an outdoor control sample. If the numbers do not clear, we re-clean at no additional cost. You get the lab report and a clearance document for your records or your insurance claim. Results come back in 24 to 48 hours.

Stage 5

Tools & methods

Tools And Methods We Use

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Dry Ice Blasting Machine

Fires rice-sized dry ice pellets at 300 to 500 mph to freeze and lift mold off structural surfaces. We run 300 to 600 pounds of pellets per shift, depending on the surface and contamination level.

02

Thermal Imaging Camera

Finds hidden moisture behind walls, under floors, and in ceilings. We use it during the inspection to map the mold and locate the water source before we scope the job.

03

Borescope Camera

Lets us see inside wall cavities and ductwork without cutting large openings. This is how we blast framing through small access ports instead of tearing out drywall.

04

HEPA Vacuum And Air Scrubber

Captures airborne spores during and after blasting. We run a HEPA vacuum at the containment edge and an air scrubber inside the space to keep the air clean.

05

Negative Air Machine

Maintains negative pressure inside the containment so spores cannot escape into clean areas. We use Abatement Technologies and Dri-Eaz units with HEPA filters.

06

Spore Trap Sampler

Collects air samples before and after remediation. We compare the indoor count to an outdoor control sample to confirm the job is clear.

07

Fogger And Ozone Generator

Treats areas that blasting cannot reach, such as inside ductwork and wall cavities. We use a fogger with disinfectant and an ozone generator for odor removal after the mold is gone.

Use cases

When To Use Dry Ice Blasting For Mold

These examples show how the service framework adapts rather than forcing every call through one repair.

Dry Ice Blasting Mold
Crawl Space Mold In A 1950s Valley Village Ranch HomeA slab leak had been feeding moisture into the crawl space for months. The floor joists and subfloor were covered in black mold growth, and the homeowner noticed a musty odor in the living room. The crawl space had no vapor barrier and standing moisture on the soil. → We contained the crawl space, ran dry ice blasting for five hours, HEPA vacuumed, and applied antimicrobial. The post-remediation test cleared on the first try. We installed a vapor barrier, and the musty odor was gone within 48 hours.

Attic Mold After A Roof Leak In Studio City

A roof leak went unfixed for one rainy season. Mold spread across 200 sq ft of roof sheathing and into the insulation. The homeowner was getting headaches and allergy symptoms and could not figure out why. → We dry ice blasted the sheathing and rafters, removed the affected insulation, and encapsulated the wood. The lab report showed spore counts back to normal outdoor levels. The homeowner had the roof repaired the following week.

HVAC Mold Contamination In A North Hollywood Restaurant

The rooftop HVAC unit had mold growing inside the plenum and on the coils. Every time the system ran, it pushed musty air into the dining room. Two other companies quoted a full system replacement at over $18,000. → We contained the unit and dry ice blasted the plenum and coils after hours. A fogger treated the ductwork, and post-remediation testing cleared before the restaurant opened the next morning. The owner kept the existing system.

Problems we solve

Mold Problems We Solve With Dry Ice Blasting

Dry ice blasting mold in VALLEY VILLAGE California for structural remediation solves problems that chemical washing and sanding cannot. Here are the most common situations we get called for, and what happens if you leave them alone.

ISSUE

Crawl space mold on floor joists and subfloor

We contain the crawl space, blast the joists and subfloor with dry ice, HEPA vacuum, and apply antimicrobial. Most crawl spaces finish in one day. We also recommend a vapor barrier to stop the moisture that feeds the mold.

SYMPTOM

Attic mold on roof sheathing after a leak

We test the growth, then dry ice blast the rafters and sheathing without soaking the wood. Encapsulation follows if the mold was deep. We also identify the leak source so you can get it fixed before the next rain.

SIGN

HVAC mold contamination in the plenum and coils

Dry ice blasting is safe for HVAC components, so we clean the plenum, coils, and interior ductwork without pulling the equipment. We follow with a fogger to treat the areas blasting cannot reach. Most systems are back online the same day.

ALERT

Bathroom mold behind tile and under vanities

We use a borescope camera to check inside the wall, then blast the framing through small access ports instead of tearing out the whole wall. That saves you the cost of drywall replacement and repainting.

Pricing process

Dry Ice Blasting Mold Pricing In VALLEY VILLAGE

$1,800 - $6,500 for most residential jobs; $8,000+ for commercial

Phase 01

Square footage of contamination

A single bathroom or small attic starts around $1,800. A full crawl space under a 1,500 sq ft home runs $3,500 to $5,500. Commercial jobs over 5,000 sq ft start at $8,000. Square footage is the biggest driver of price.

Phase 02

Containment complexity

A simple containment in an open crawl space takes two hours to build. A multi-room containment with HVAC sealing and negative air ducting can take a full day. Complex containments add $500 to $1,500 to the job.

Phase 03

Dry ice consumption

We consume 300 to 600 pounds of dry ice pellets per shift. Heavy contamination on rough surfaces like brick or concrete uses more pellets than smooth lumber. Dry ice runs $1.50 to $3.00 per pound, so consumption directly affects the price.

Questions before we arrive

Frequently Asked Questions About Dry Ice Blasting Mold

Dry Ice Blasting Mold
Call (833) 929-5837
How much does dry ice blasting mold cost in VALLEY VILLAGE California?

Most residential dry ice blasting mold jobs in VALLEY VILLAGE run $1,800 to $6,500 in 2026, depending on square footage and containment. A single bathroom or small attic starts around $1,800. A full crawl space or commercial HVAC system can run $8,000 or more. The price includes containment, blasting, HEPA vacuuming, antimicrobial treatment, and post-remediation testing.

Is dry ice blasting safe for mold removal in VALLEY VILLAGE California?

Yes. Dry ice blasting is non-toxic, non-conductive, and leaves no chemical residue. The dry ice sublimates into carbon dioxide gas, which we vent through the containment. We use respirator cartridges and follow Cal/OSHA standards for worker safety. The process is safe for wood, brick, concrete, and most electrical components, and it does not introduce moisture that would feed new mold growth.

How long does dry ice blasting take in VALLEY VILLAGE California?

A typical single-room job takes four to six hours from containment setup to final HEPA vacuuming. A full crawl space or attic runs one to two days. Commercial jobs over 5,000 sq ft can take three to five days. We give you a time estimate in the written scope, and we do not leave until the post-remediation test clears.

Who does dry ice mold removal near me in VALLEY VILLAGE California?

Mold Remediation Service Valley Village does. We are a local company based in the Valley, licensed through the CSLB, and certified by the IICRC and ACAC. Call (833) 929-5837 for a same-day inspection. We serve Valley Village, Studio City, North Hollywood, Sherman Oaks, and the surrounding San Fernando Valley communities.

Ready when you are

Get Dry Ice Blasting Mold in VALLEY VILLAGE, California

If you have visible mold growth, a musty odor, or a recent leak, call (833) 929-5837. We answer 24/7, schedule same-day inspections, and give you a fixed price before any work begins. Our dry ice blasting mold service in VALLEY VILLAGE includes post-remediation testing and a written clearance report.

Dry Ice Blasting Mold

Talk with the local team

Request Dry Ice Blasting Mold

Call (833) 929-5837 any time, day or night, and a live dispatcher will set up your inspection. We answer 24/7 for emergencies and schedule same-day appointments whenever our crews have an opening. If you prefer email, send us your address and a short description of what you are seeing, and we will get back to you the same business day.

12125 Riverside Dr, Valley Village, CA 91607, USA, VALLEY VILLAGE, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now